ผลการค้นหา

in creation

แปลว่าน่าแปลก (ใช้ตามหลัง who, what, when, where, how, which)

BACKUP BOTTLE

แปลว่า(english) A vessel, normally cylindrical, which is used to store gas for future release of the energy in the compressed gas to an accumulator.

Black Oil Tempered Spring Steel Strip (Scaleless Blue)

แปลว่า(english) A flat cold rolled usually .70/.80 medium high carbon steel strip, blue-black in color, which has been quenched in oil and drawn to desired hardness. While it looks and acts much like blue tempered spring steel and carries a Rockwell hardness of C44/47, it has not been polished and is lower in carbon content. Used for less exacting requirements than clock spring steel, such as snaps, lock springs, hold down springs, trap springs, etc. It will take a more severe bend before fracture than will clock spring, but it does not have the same degree of spring-back.

Bending Angle

แปลว่า(english) A 'V-shaped' piece of angle iron attached to the rear of the coil car in the Strip Steel, which is used to help the operator put bends into the front end of a coil.

Greenhouse gases

แปลว่า(Environmental Engineering) Gases which trap solar radiation. Of the solar energy entering the earth's atmosphere a portion is reflected back and a portion penetrates onto the earth's surface. The portion reflected back from the earth's surface is at a different wavelength that when it entered. Carbon dioxide and other gases, which pass solar radiation, absorb this reflected radiation, increasing the earth's temperature. This is much like a greenhouse, hence the name.

Blister

แปลว่า(english) 1) Coating defect consisting of the formation of bubbles in a coating, which appear as hemispherical elevations. The blisters are hollow, and are usually caused by entrapped air or solvent. 2) A raised spot on the surface on the surface of metal due to expansion of gas which causes a subsurface metal separation such as inclusions and small laminations.

ACCUMULATOR

แปลว่า(english) A vessel, normally cylindrical, which is used to store fluid and gas for future release of the energy in the compressed fluid and gas. Normally contains a diaphragm or piston between the fluid (liquid) and gas chambers. Fluid is normally introduced at one end and the gas at the opposite end.

Bottle Top Mold

แปลว่า(english) Ingot mold, with the top constricted; used in the manufacture of capped steel, the metal in the constriction being covered with a cap fitting into the bottle-neck, which stops rimming action by trapping escaping gases.

Hydrogenesis

แปลว่า(Concrete Engineering) Another term for condensation. The term is especially applied to base and soil substrates under highway pavements. where the barometric pump causes the inhalation of humid air, which then condenses in those structures, causing an ever increasing moisture content and sometimes instability.

Blowhole 2

แปลว่า(english) A cavity which was produced during the solidification of metal by evolved gas, which in failing to escape is held in pockets.

AAC - Autoclaved Aerated Concrete

แปลว่า(Concrete Engineering) Exceptionally lightweight precast concrete with high thermal qualities and fire resistence. Suitable for cutting with ordinary hand tools. Mix design is composed of portland cement, sand or siliceous material, lime, gypsum, finely powdered aluminum, and water. Initial mix is a combination of portland cement, sand, lime and gypsum to produce a slurry. Finely powdered aluminum mixed into a paste is added prior to placement into large, rail-like forms. The finely powdered aluminum reacts with the alkaline components of the cement and lime to produce hydrogen gas, which increases the volume approximately five times producing a uniformly, dispersed cellular structure. Units are cut to required shape. Units are placed in an autoclave, an enclosed pressurized chamber, and steam cured at 3500 F. Approximately 80% of the ultimate volume consists of air voids.

Backer (back-up plate)

แปลว่า(english) A “tool” or reinforcing part, which presses against the outer surface of an extrusion die, supporting it against the pressure of the extruding metal. The backer has an opening larger than the die aperture, allowing the extruded product to emerge without marring its soft surface.